---
# Satellite 1 HAT Board – peripheral controller
#
# Runs alongside the linux-voice-assistant container.
# Connects to LVA's peripheral WebSocket API (port 6055) and drives the
# 12-LED SK6812 ring and four hardware buttons on the Satellite 1 HAT.
#
# IMPORTANT – read the hardware notes at the bottom of this file before
# starting the container for the first time.

services:
  satellite1-peripheral:
    build: .
    image: lva/satellite1_hat_board:local
    container_name: satellite1_hat_board
    restart: unless-stopped

    # -----------------------------------------------------------------------
    # PWM + DMA access (required by rpi-ws281x for LED ring control)
    #
    # rpi-ws281x drives the SK6812 LEDs via hardware PWM (GPIO 12, channel 0)
    # and DMA.  This requires access to /dev/mem for DMA buffer allocation.
    # There is no narrower capability; privileged is the practical requirement
    # on Raspberry Pi OS when using PWM mode.
    # -----------------------------------------------------------------------
    privileged: true

    # -----------------------------------------------------------------------
    # Device access
    # -----------------------------------------------------------------------
    devices:
      # GPIO memory map – needed by RPi.GPIO for button input
      - /dev/gpiomem:/dev/gpiomem
      # Full physical memory map – needed by rpi-ws281x DMA engine
      - /dev/mem:/dev/mem
      # Video core mailbox – used by rpi-ws281x to allocate DMA buffers
      - /dev/vcio:/dev/vcio

    # -----------------------------------------------------------------------
    # Run as root inside the container.
    # rpi-ws281x's DMA allocator requires root access to /dev/mem and /dev/vcio.
    # -----------------------------------------------------------------------
    user: "0:0"

    group_add:
      # gpio group – allows RPi.GPIO to open /dev/gpiomem without root
      # (redundant when user is root but good practice to keep for non-root builds)
      - gpio

    # -----------------------------------------------------------------------
    # Environment variables
    # -----------------------------------------------------------------------
    environment:
      - PYTHONUNBUFFERED=1

    # -----------------------------------------------------------------------
    # Network
    #
    # Uses the host network so "localhost" resolves to the Pi itself and
    # the LVA container's port 6055 is directly reachable.
    # If LVA is on a different host, change --host below to its IP address
    # and remove network_mode: host.
    # -----------------------------------------------------------------------
    network_mode: host

    # -----------------------------------------------------------------------
    # Command-line arguments passed to Satellite1_HAT_Board.py
    # -----------------------------------------------------------------------
    command:
      - "--host"
      - "localhost"        # Change to LVA container IP if on a different host
      - "--port"
      - "6055"
      # Uncomment for verbose logging during setup / troubleshooting:
      # - "--debug"

    # -----------------------------------------------------------------------
    # Health check – verifies the process is still running
    # -----------------------------------------------------------------------
    healthcheck:
      test: ["CMD", "pgrep", "-f", "Satellite1_HAT_Board.py"]
      interval: 30s
      timeout: 5s
      retries: 3
      start_period: 15s

    # -----------------------------------------------------------------------
    # Logging – keep last 10 MB across 3 rotated files
    # -----------------------------------------------------------------------
    logging:
      driver: "json-file"
      options:
        max-size: "10m"
        max-file: "3"


# =============================================================================
# HARDWARE NOTES – read before first run
# =============================================================================
#
# 1. SPI / PWM KERNEL OVERLAY
#    rpi-ws281x can drive LEDs via PWM (recommended), PCM, or SPI.
#    This compose file uses PWM on GPIO 12 (PWM0, channel 0).
#    Add the following line to /boot/firmware/config.txt (or /boot/config.txt
#    on older Raspberry Pi OS):
#
#        dtoverlay=pwm,pin=12,func=4
#
#    Then reboot.  Without this overlay the PWM pin is not mapped and the
#    LED ring will not light up.
#
#    Alternatively, SPI mode can be used (GPIO 10, SPI0 MOSI).  If you prefer
#    SPI, enable it via:
#        dtoverlay=spi0-1cs
#    and change LED_GPIO_PIN to 10 and LED_CHANNEL to 0 in satellite1_peripheral.py,
#    then also set LED_DMA to 10 and remove the need for /dev/vcio.
#
# 2. AUDIO CONFLICT WITH PWM
#    The Raspberry Pi's onboard audio also uses PWM.  If you use the 3.5 mm
#    headphone jack, it conflicts with PWM0.  Disable onboard audio in
#    /boot/firmware/config.txt:
#
#        # dtparam=audio=on    ← comment this out
#
#    The Satellite 1 HAT has its own I2S audio codec (XMOS XVF3800), so
#    onboard audio is not needed.
#
# 3. SATELLITE 1 HAT I2S AUDIO DRIVER
#    The HAT's microphone array is driven by the XMOS XVF3800 over USB.
#    No additional kernel driver is required — it enumerates as a standard
#    USB audio device.  LVA picks it up automatically via soundcard.
#    If you use the Satellite 1 HAT's line-out, add to config.txt:
#
#        dtoverlay=hifiberry-dac
#
# 4. GPIO GROUP
#    Make sure the user running Docker belongs to the gpio and spi groups
#    on the host:
#
#        sudo usermod -aG gpio,spi $USER
#
# 5. MEMORY SPLIT (optional)
#    On Pi Zero 2 W, increase GPU memory to at least 64 MB so the VideoCore
#    mailbox has enough address space for the DMA allocator:
#
#        gpu_mem=64    (in /boot/firmware/config.txt)
#
# =============================================================================